Termite Control Centurion - An Overview
DO NOT waste lure by adding it into timbers that do not contain live termites. The colony is murdered only if workers take enough of the bait back to the nest. And they'll only take it if they can harvest it, undisturbed, from inside the ruined timber you've found. .
See the uneven surface of the window frame. Termites had eaten it out, in some regions leaving only the paint.
An Unbiased View of Termite Control Can Also Be Done By
Make an opening into the termites using a pointed knife or fine screwdriver. The hole should be no bigger than about 5mm diameter to begin with. (It should be enlarged only when it is time to add the cache of bait). You can pry into the surface of the timber in which it seems spongy, thin or hollow.
It's only as a last resort you should attempt to open a tunnel on a timber or foundation surface. .
Once you have broken into into where it's hollow, wait for a minute or so. If termites are there, the soldiers normally come to guard the opening while employees repair it. You will see their antennae and their heads blocking the hole. If no live termites appear, leave the hole open and return later or check next day.
The 5-Minute Rule for Termite Control Centurion
This reveals the way planters will come out from the infested timber into a foil coated mass of lure taped to the surface. Alternatively, if the surface is flat, the feeder might be fixed within the hole and the termites will enter it to crop the bait.
If the wood has a flat surface, then make the hole away from corners so you can line it up with the hole in the base of the feeder. If the access hole into the termites is on a round post or another situation where you cannot fix the feeder to it, then you can make a pouch of aluminium foil and duct tape to hold the bait in place.
If you're using the foil method, carefully pull back the border of the sticky tape to inspect and to replenish the lure. If you're using the feeder system, it is not as disturbing if you can add more bait to the original feeder.
The termites you will see as dark brown nests high up in look at more info a tree are seldom pests of significance. But the main subterranean termites which do that 99 percent of the $damage we mentioned before, will often nest inside the central pipe or hollowed out center of a mature tree. Mastos, the giant northern termite, dont constantly wait for the decay of this pipe.
Some Known Questions About Termite Control Can Also Be Done By.
(See the special box on Mastos).
If at colonising flight period a termite couple find their way into a hollow tree through possibly a dead/broken-off branch or in via a scar from flame at the top article bottom they could not possibly have better conditions. Requires plenty to eat, moisture and protection. A 50 metre traveling to your home would not be out of the question. .
If you've got a large eucalypt, peppercorn or a mature fruit tree nearby, you should check it. Utilize an 15-20mm auger little long enough to drill into the centre of the trunk at about shoulder height. Drill at a slight downward angle and when you are feeling less resistance it'll be because you have reached the pipe.
Some Known Details About Termite Control Can Also Be Done By
If not, you could slip in a long thin grass leaf into the drill hole, then leave it for a minute and withdraw it gradually. Termites might be found holding on, attacking it. If no live termites are found, return in half an hour or even next morning; if there's termite life inside, they'll be repairing or have mended the opening using their mud mixture. .
In this situation you dont need to see live termites; its just more satisfying to know you have actually killed a colony when you take the next steps
Re-open the drill hole if it's been repairedUsing a funnel, plastic tube and watering can/bucket, pour at least 20-30 litres of a chlorpyrifos or a bifenthrin solution down into the tree. These insecticidal concentrations can be purchased from a local hardware store. They could be known by several brand names but the active ingredients are on the front panel of the tag.